บริษัท น่ำแซอินเตอร์เทรดดิ้ง จำกัด : Servo Pulse and Tension Controller

PAGE VIEW : 14,510

Product Information :

Name :

Servo Pulse and Tension Controller

Category :

เครื่องจักร, อุปกรณ์เกี่ยวกับเครื่องจักร, เครื่องมือกล

Sub - Category :

11 Miki Pulley Electro-Magnetic Clutch and Brake

Brand :

Miki Pulley

Model :

SPC-011, SPC-2000, SPC-007, SPC-501

Product Type :

สินค้า, ผลิตภัณฑ์

Short Description :

Controllers Introduction of control systems is gaining for automated machinery in various fields. Especially, position control systems are used for all kinds of automated machinery. We offer various controllers suitable for fixed position-to-position control, synchronous (follow-up) control and biaxial interpolation control. Also, a controller that controls a powder brake voltage to obtain a stable tension control is available. Troublesome task in the process of system construction is reduced by our easy-to-operate controllers with advanced controls. SPC-PULCON (SPC-2000) The SPC-PULCON is a controller suitable for a biaxial (2-shaft) control. For X-Y table purposes, the SPC-2000-P is available. Arc interpolation, linear interpolation and teaching function are included. A small-scale program operation can be performed. Programming is easy by entering a simple command and necessary data with commonly-used spreadsheet software. A handshake function is also included by I/O. For synchronous (follow-up) control purposes, the SPC-2000-S is available. This model synchronizes two shafts with the other shaft operation. There are three types of synchronous patterns, proportional synchronization, reciprocating synchronization and two-speed synchronization (rotary cutter) to assign the required patterns to the two shafts. Since the operation patterns are set in advance, no programming is required. The operation can be performed simply by setting the roll diameter of the device, decelerating ratio, servo resolution, maximum rotation speed or rotational direction. SPC-SYNCHRO (SPC-011-SYNC) The SPC-SYNCHRO synchronizes one shaft with the other shaft operation. There are three types of synchronous patterns as well as SPC-2000-S, proportional synchronization, reciprocating synchronization and two-speed synchronization (rotary cutter). The functions conform to the SPC-2000-S. Controlling shaft number is 1. SPC-007 Model A mark control needed for use in roll feeder is enhanced. Feed length is automatically updated by following the change of mark interval to keep a stopping accuracy. It can be synchronized with a tool such as a cutter with up-and-down motion. By a function to stabilize the ratio of the time needed for tool cycling and feeding, a feeding speed is automatically updated as tool cycle time changes, which prevents a tool from getting caught during feeding of material. SPC-501 Model This is an open-loop controller by integrated thickness detection for powder brakes (clutches). It is suitable for a tension control when feeding and taking up a film, paper or thread. This control method outputs a voltage commensurate with the take-up diameter calculated by integrating sensor signals attached to a take-up spindle. A feed-back loop by a sensor for precise detection of actual tension is not performed. However, it is easy to adjust and there is no instability. A tension detection sensor is not required that the cost can be reduced.

Product Detail :

Controllers

Introduction of control systems is gaining for automated machinery in various fields. Especially, position control systems are used for all kinds of automated machinery. We offer various controllers suitable for fixed position-to-position control, synchronous (follow-up) control and biaxial interpolation control. Also, a controller that controls a powder brake voltage to obtain a stable tension control is available. Troublesome task in the process of system construction is reduced by our easy-to-operate controllers with advanced controls.

Servo Pulse Controller

A servo pulse controller is used to control the operation when using a servo or stepping motor for the drive member. Miki Pulley's controllers are designed for performance improvement according to application. Any actuator compatible with pulse input is connectable. The SPC-007 model for roll feed control, SPC-PULCON for X-Y control and SPC-SYNCHRO for synchronous (follow-up) control are available.

SPC-PULCON (SPC-2000)

The SPC-PULCON is a controller suitable for a biaxial (2-shaft) control. For X-Y table purposes, the SPC-2000-P is available. Arc interpolation, linear interpolation and teaching function are included. A small-scale program operation can be performed. Programming is easy by entering a simple command and necessary data with commonly-used spreadsheet software. A handshake function is also included by I/O. For synchronous (follow-up) control purposes, the SPC-2000-S is available. This model synchronizes two shafts with the other shaft operation. There are three types of synchronous patterns, proportional synchronization, reciprocating synchronization and two-speed synchronization (rotary cutter) to assign the required patterns to the two shafts. Since the operation patterns are set in advance, no programming is required. The operation can be performed simply by setting the roll diameter of the device, decelerating ratio, servo resolution, maximum rotation speed or rotational direction.

Controlling shaft number	2 shafts
Operational power supply	DC24V+/-10% 0.5A DC5V+10% 1A
Operating environment	0^oC to 50^oC 85%Rh or less

SPC-SYNCHRO (SPC-011-SYNC)

The SPC-SYNCHRO synchronizes one shaft with the other shaft operation. There are three types of synchronous patterns as well as SPC-2000-S, proportional synchronization, reciprocating synchronization and two-speed synchronization (rotary cutter). The functions conform to the SPC-2000-S. Controlling shaft number is 1.

Controlling shaft number	1 shaft
Operational power supply	DC24V+/-10% 0.5A DC5V+10% 1A
Operating environment	0^oC to 50^oC 85%Rh or less

2D CAD data |

SPC-007 Model

A mark control needed for use in roll feeder is enhanced. Feed length is automatically updated by following the change of mark interval to keep a stopping accuracy. It can be synchronized with a tool such as a cutter with up-and-down motion. By a function to stabilize the ratio of the time needed for tool cycling and feeding, a feeding speed is automatically updated as tool cycle time changes, which prevents a tool from getting caught during feeding of material.

Controlling shaft number	1 shaft
Operational power supply	DC24V+/-10% 0.5A DC5V+5% 0.5A
Operating environment	0^oC to 50^oC 85%Rh or less

Catalog |

Manual |

2D CAD data |

Tension Controller

When rolling up a film, fabric or thread, the diameter differs between beginning and end of take-up, and the tension added to the material constantly varies. If stretch material is not taken up with constant tension, it leads to a product failure. A tension controller changes the torque on the take-up side to control the tension to be constant regardless of diameter. As a control method, there are a "close droop method" that detects an actual tension by a tension sensor to control torque and "open loop method" that detects integrated thickness to control torque by the result of calculation.

SPC-501 Model

This is an open-loop controller by integrated thickness detection for powder brakes (clutches). It is suitable for a tension control when feeding and taking up a film, paper or thread. This control method outputs a voltage commensurate with the take-up diameter calculated by integrating sensor signals attached to a take-up spindle. A feed-back loop by a sensor for precise detection of actual tension is not performed. However, it is easy to adjust and there is no instability. A tension detection sensor is not required that the cost can be reduced.